Matrix T5 Manuel d'utilisateur

1R SPRT SP-T5 Portable Dot Matrix Printer User’s Manual

10Temperature/HumidityStorage Temperature/Humidity-20℃～60℃/5％～95％ Chapter 3 Operation 3.1 Using Preparation 3.1.1 Battery Installation 3.1.2 Paper

11 3.2 Operation Specification 3.2.1 Printer On/Off The printer is powered on by pressing the power button for about 1 second; the power indicator i

123.2.2 Self-test The self-test checks the printer’s current settings, status and whether the printer has any problems. Turn on the power while holdi

13printer, so the power charging begins, during the course of power charging, the charging indicator goes red, and turns to blue when the charging is

14Data Bit: 7 bit, 8 bit optional Parity: Odd, Even, None optional Stop Bit: 1 bit The ex-factory default setting is: Baud rate: 9600bps Handshakin

15please don’t use this pin if making connecting line, otherwise the printer might be not used normally or damaged. When prints large quantities of

16RAW-Ir can work under 9600bps, 19200bps, 38400bps, 57600bps, 115200bps, the baud rate of RAW-Ir is same to that of serial interface. Notice: 1) To

173. If there are other Bluetooth devices, please select T5 Bluetooth Printer; 4. Put in password “1234” 5. Pairing finished. Notice: If the printe

18The printer also can be set to turn off automatically mode by T5 Setting Tools. In turn off automatically mode, the printer will power off if witho

19 3.5 Indicators and Buzzer There are three indicators for T5 printer, they are 【POWER】,【MODE】 and 【FEED】, the 【POWER】and 【MODE】 indicators are b

2 Content Content... 2 Operating Precautions...

20Solid blue (middle) Charging finish － Solid red(middle) Charging － Solid purple(middle) Battery error 3.6 Printer setting Users can set the prin

21mark position 4.1.4 LF Print and feed line 4.1.5 CR Print and carriage return 4.1.6 ESC J n Print and feed paper for n lines 4.1.7

224.3.6 ESC SP n Set line character spacing 4.3.7 GS L nl nH Set left spacing 4.3.8 ESC a n Set alignment Graphic/Image print commands 4.

23[Format]： ASCII ESC @ Hexadecimal 1B 40 Decimal 27 64 [Description]：Clear the data in the print buffer; Restore the default of each pr

24Decimal 12 [Description]:Print and feed paper to the position of black mark, if there is no black mark, then feed paper about 30mm and stop, th

25[Notice]: Sets the print starting position to the beginning of the line. 4.1.6 ESC J n [Name]: Print and feed paper [Fo

264.1.8 HT [Name]: Horizontal tab [Format]: ASCII HT Hexadecimal 09 Decimal 9 [Description]: Moves th

27[Format]: ASCII ESC ! n Hexadecimal 1B 21 n Decimal 27 33 n [Description]: Select print mode(s) using n as follows: Bit V

28setting of the last received command is effective. • ESC + can also select character size. However, the setting of the last received command is eff

29n Description 0 Cancel underline 1 Select underline (1 dot width) [Reference]: ESC ! 4.2.4 ESC E n [Name]: Select／Cancel bold font print

33.3.3 （Bluetooth）Interface... 16 3.4 Other Functions... 17 3.4.1 Stan

30[Description]: If n=1，select reverse print；n=0，cancel reverse print。Default set n=0。 4.2.7 ESC V n [Name]：Select/cancel character rotation

31print position is [( nL + nH × 256) (vertical or horizontal motion unit)] inches. [Notice]: Settings outside the specified printable area are ignor

32• Transmit [ n] k in ascending order and place a NUL code 0 at the end. • When [ n] k is less than or equal to the preceding value [ n] k-1, tab se

33• The print starting position moves from the current position to [ N × horizontal motion unit] 4.3.4 ESC 2

34 Should input the command：1B 33 03 4.3.6 ESC SP n [Name]: Set character spacing [Format]: ASCII ESC SP n Hexadeci

35position, Set n horizontal dot spacing as the character’s left spacing, nL nH are n’s LSB and MSB, N=nL + nH × 256. [Default]: n=0，that means there

36[Description]: Selects a bit-image mode using m for the number of dots specified by n1 and n1, as follows: m Vertical Dot Number (Height) Horizon

37• If x*y is off-limit, then the command is forbidden. • d means the image data. 1 print, 0 not print • use this command to define the downloaded bi

38Hexadecimal 1D 50 n Decimal 29 80 n [Description]：0<=n<=9.Print prestored bit-image, the number of image is 1<=n<=9 [Note]:

39command is used to print n line segments on one horizontal line. Using the command continuously can print out the line segment the user required. •

44.2.7 ESC V n ... 30 4.3 Print setting commands... 30 4.3.1

40want to print other characters, then need to set the character code to 0 or 1; • Only can print 2 characters on each horizontal dot line. [Referenc

414.6 User-defined character commands 4.6.1 ESC % n [Name]: Select/cancel user-defined character [Format]: ASCII ESC % n Hexade

42[Range]: y = 3, font A (12 × 24), y = 2, font B (8× 16), 32 ≤ c1 ≤ c2 ≤ 126 x = 12, font A (12 × 24), x = 8, font B (8× 16), 0 ≤ d1 ... d(y × xk) ≤

43 • Defining the data of user-defined character is (y × x) bytes. • Setting the printing dot’s corresponding bit is 1 or non-printing dot’s one is

44• The user-defined characters will be deleted in the following situation: 1. Carry out ESC @. 2. Printer reset or power turn off. [Default] Built-i

45Chapter 5 Appendix Character Set

5 Operating Precautions This section presents important information intended to ensure safe and effective use of the printer. Please read the followi

6 Notes on Using Be sure not to print continuously over 1 meter, otherwise may cause damage to the print head. Water or other liquid should not spill

7 Be sure to use up the electricity of the battery before charge it, as it can ensure the using life of the battery. Notes on Handling The printer s

8Chapter 1 Outer Appearance and Accessories 1.1 Outer Appearance 1.2 Standard Accessories Power Adaptor 1 unit Rechargeable Li-ion Battery 1 uni

9Physical Specification Outer Dimension 112×98×46（L×W×H） Weight 340g（Paper roll excluded） Paper Diameter ≤60mm Printing Specification Printing Metho